Viega Eco Plus sink basin element
Product information
Viega Eco Plus sink basin element
for sink basins
| Year built (from): | 2002.11.26. |
Trade mark rights exist for this document, further information can be found at viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and sanitary professionals and trained personnel
SHK-FachkräfteConsumers
It is not permitted for individuals without the abovementioned training or qualification to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
INFO!
Notes give you additional helpful tips.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at viega.com/standards .
Regulations from section: Fields of application / Mounting conditions
Scope / Notice | Regulations applicable in Germany |
|---|---|
suitable masonry walls | EN 1996‑1‑1 |
suitable concreted walls | DIN 1045 |
suitable support profiles | DIN 18183 |
Regulations from section: Sound protection
Scope / Notice | Regulations applicable in Germany |
|---|---|
Fulfilled noise protection requirements | DIN 4109 |
Fulfilled noise protection requirements | DIN 4109 (additional sheet 2) |
Fulfilled noise protection requirements | VDI 4100 SSt I-SSt II |
Product description
Overview
- 1 - Viega Eco Plus element
- 2 - connections for wall plates
- 3 - mounting panel
- 4 - mounting bracket for drain elbow
- 5 - drain elbow
- 6 - adjustable feet
Compatible components
The element is compatible with all common sink basins.
Sound protection
The sink basin element complies with the noise insulation requirements specified in section Regulations from section: Sound protection .
Technical data
The product has the following technical data:
drain elbow |
|---|
Hole diameter for fixing in wooden frame construction |
Construction height |
DN 50 |
11 mm |
1300 mm |
Accessories
Required accessories
The fixing set model 8173 is required to secure.
Handling
Assembly information
Mounting conditions
Suitable walls
The element is suitable for mounting on masonry wall constructions and support profiles pursuant to the regulations in section Regulations from section: Fields of application / Mounting conditions .
The element may only be mounted on even wall surfaces.
Construction height
With the construction height, the marked height of the upper edge of the finished floor must be observed.
Installation dimensions
Required tools
The following tools are required for mounting the sink basin element:
drill with 10 mm drill bit
ratchet with sockets: 13 mm / 17 mm
fork or ring spanner: 13 mm / 17 mm
Assembly
Mounting the element
Masonry wall
INFO!
Masonry and concreted walls
You should use a support bracket (model 8165) when mounting multiple sink basin elements with an interval of > 490 mm. Observe the instructions for use of the support bracket when mounting.
-
Determine and mark fixing points.
X1: 390 mm (model 8180.73)
X2: 440 mm (model 8173)
X3: 1280 mm
-
Drill holes.
-
Mount the fixing set with the fork spanner (size 13).
-
Align height of element.
Whilst doing so, observe the markings on the element.
Determine construction height in accordance with the on-site marking of the upper edge of the finished floor.
INFO!The construction height must be determined exactly.
There are only limited possibilities available to remedy errors made during this assembly step, Construction height .
-
Set height of the crossbeam.
The crossbeam aids the installation of the wall-mounted fitting.
-
Set the installation depth of the element with the fork spanner (size 17).
-
Remove WC element and drill floor holes.
-
Attach element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
-
Mount drain elbow in mounting bracket.
-
Secure with a bracket.
-
Set height of the drain elbow (50–100 mm).
-
Set connections for wall plates.
Observe the instructions of the fitting manufacturer.
-
Make water connections.
-
Double-clad element (2 x 12.5 mm).
Mounting in on-site support profile
The element can be inserted into the 50 mm and 75 mm support profiles.
-
Determine the fixing points.
-
Align element.
-
Mount drain elbow.
-
Set connections for wall plates.
-
If necessary, adjust the pre-mounted foot depth from 75 mm to 50 mm: Pull out foot and turn by 90°.
-
Attach element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
-
Determine construction height in accordance with the on-site marking of the upper edge of the finished floor.
-
Align height of element.
Whilst doing so, observe the markings on the element.
INFO!The construction height must be determined exactly.
There are only limited possibilities available to remedy errors made during this assembly step, Construction height .
-
Set height of the crossbeam.
The crossbeam aids the installation of the wall-mounted fitting.
-
Screw element together laterally with the support profiles.
-
Make water connections.
-
Double-clad element (2 x 12.5 mm).
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.